


CCENT (ICND1)
Network Simulator Labs
The NetSim 11
Network Simulator, Router
Simulator and Switch
Simulator provides labs designed to help you achieve the
CCENT
certification. NetSim 11 for CCENT includes labs for the
100-101 ICND1 and
the newly revised 100-105 ICND1 technologies. Each lab is written to help you understand the
technologies necessary to pass the CCENT ICND1 exam. See the
list
below for all of the labs included with
NetSim
11
for CCENT.
NetSim 11
for CCENT 100-101 Lab
Topics
- ACL Practice Lab 1 - Standard
ACLs
- ACL Practice Lab 2 - Standard
ACLs
- ACL Practice Lab 3 - Extended
ACLs
- ACL Practice Lab 4 - Extended
ACLs
- ACL Practice Lab 5 - Named
ACLs
- ACL Practice Lab 6 - Named
ACLs
- Address Resolution
Protocol
- Advanced Router
Configuration
- Backup Using
TFTP
- Basic Debugging
- Basic
Network Services I
- Basic Network Services
II
- Basic Router
Configuration
- Basic Show
Commands
- Cisco Discovery
Protocol
- Cisco Discovery Protocol on a
Router
- Configuring DNS
I
- Configuring IPv6 I
- Configuring
IPv6 II
- Configuring Network Address Translation
I
- Configuring Network Address Translation
II
- Configuring NTP Authentication
I
- Configuring NTP Authentication
II
- Configuring NTP I
- Configuring
NTP II
- Configuring
PPP-PAP-CHAP
- Configuring Router
Interfaces
- Configuring Single-Area
OSPFv3
- Configuring Static and OSPFv3
Routing
- Configuring
Trunking
- Configuring
VLANs
- Creating a Host
Table
- Default Routes
- Deleting
VLANs
- DHCP
- DHCP
II
- DHCP Relay Agents I
- DHCP
Relay Agents II
- Dynamic
NAT
- Enhancing Switch Security
I
- Enhancing Switch Security
II
- Extended Access Lists
- Frame
Relay Hub-and-Spoke
- Frame Relay
I
- IGRP
- IGRP
Routes
- Initial Switch
Configuration
- IP Addressing on a
Router
| - IP Addressing on a
Switch
- Loopback
Interfaces
- Many-to-One NAT
- Named
Extended Access Lists
- NAT Overloading -
PAT
- NAT Pool
- Numbered Access
Lists
- OSPF I
- OSPF
II
- RIP
Routes
- RIPv2
- RIPv2
Routes
- Router Basics I
- Router
Basics II
- Router Remote Access via
Telnet
- Routing Information Protocol
I
- Saving Router
Configurations
- Setting up a Serial
Interface
- Standard Access
Lists
- Static NAT I
- Static NAT
II
- Static Routes I
- Static Routes
II
- Switch and Workstation
Configuration
- Switch Basics
I
- Switch Basics II
- Switch Remote
Access via Telnet
- Telnet
I
- Telnet II
- Testing Connectivity
with Traceroute
- Trivial File Transfer
Protocol
- Troubleshooting a Network
Topology
- Troubleshooting
DHCP
- Troubleshooting DNS
I
- Troubleshooting DNS
II
- Troubleshooting Network
Configuration
- Troubleshooting
NTP
- Troubleshooting
PPP-PAP-CHAP
- Troubleshooting
RIP
- Troubleshooting VLSM
- Using
the System Configuration Dialog for Initial Switch
Configurations
- VLSM Practice
I-D
- VLSM Practice II-D
- VLSM
Practice III-D
- VLSM Practice
III-M
- VLSM Practice II-M
- VLSM
Practice
I-M
|