Special Offers | My Account | Log In
  0 items in your cart


Search: Boson Sites | Products

NetSim for CCENT




CCNP Network Simulator Labs

NetSim Network Simulator and Router Simulator provides labs designed to help you achieve the CCNP certification. Each lab is written to help you understand the technologies necessary to pass the CCNP exam. See the list below for all of the labs included with NetSim for CCNP.

Lab Topics for CCNP

  • AAA Authentication
  • AAA Login Authentication and Exec Authorization
  • Address Optimization
  • Address Resolution Protocol (ARP)
  • Advanced Extended Access Lists
  • Advanced Router Configuration
  • Applying Security Tools
  • Backup a WAN Connection with IPSec VPN
  • Backup Interface
  • Backup Using TFTP
  • Basic Debugging
  • Basic Router Configuration
  • Basic Show Commands
  • BGP
  • CHAP and RIP
  • Cisco Discovery Protocol (CDP)
  • Configuring a Switch for a WLAN
  • Configuring Class-Based Header Compression
  • Configuring EIGRP
  • Configuring FIFO and WFQ Queing Mechanisms
  • Configuring Frame Relay Mode MPLS
  • Configuring Hot Standby Router Protocol (HSRP)
  • Configuring IOS Security Part I - VLAN ACLs
  • Configuring IOS Security Part II - TACACS+
  • Configuring IPv6
  • Configuring IPv6 Routing
  • Configuring IPv6 Tunnels
  • Configuring LFI
  • Configuring Multiple HSRP groups
  • Configuring NBAR
  • Configuring Open Shortest Path First (OSPF)
  • Configuring QoS
  • Configuring QoS Preclassify
  • Configuring QoS with Cisco AutoQoS
  • Configuring Router Interfaces
  • Configuring Static and OSPFv3 Routing
  • Configuring Support for IP Telephony
  • Configuring Telnet on Catalyst 2950 Switches
  • Configuring the LLQ Queing Mechanism
  • Configuring Trunking on Catalyst 2950 Switches
  • Configuring Virtual Router Redundancy Protocol (VRRP)
  • Configuring VLANs on a Catalyst 2950 Switch
  • Configuring VTP Client Mode on a Catalyst 2950 Switch
  • Configuring VTP on Catalyst 2950 Switches
  • Confirming the Network Configuration
  • Creating a Host Table
  • Default Routes
  • Deleting VLANs on a Catalyst 2950 Switch
  • Dynamic NAT
  • EIGRP
  • EIGRP and Frame Relay
  • EIGRP and Wildcard Masks
  • EIGRP Authentication
  • EIGRP Routes
  • Enhancing Switch Security
  • EtherChannel – PAgP and LACP
  • EtherChannel – Layer 2 and Layer 3
  • Expanding Switched Networks
  • Extended Access Lists
  • Extended Access Lists with RIP
  • Frame Relay
  • Frame Relay Full Mesh
  • Frame Relay Hub-and-Spoke
  • Frame Relay with Dial Backup
  • Hierarchical IP Addressing
  • ISDN Dialer Profiles
  • IGRP
  • IGRP Routes
  • Implementing IPv6
  • Implementing Multiple Spanning Tree Protocol (MSTP)
  • Implementing Network Address Translation
  • Influence EIGRP Path Selection
  • Initial Configuration
  • Initial Switch Configuration
  • Inter-VLAN Routing
  • Introduction to MQC and the SDM QoS Wizard
  • IOS Switching Initial Configuration
  • IP Access Lists
  • IP Addressing
  • IP Addressing on Catalyst 2950 Switches
  • IPSEC
  • ISDN BRI
  • IS-IS
  • Layer 3 Switching
  • Layer 3 Switching and Layer 2 Security
  • Loopback Interfaces
  • Low Latency Queuing
  • Many-to-One NAT
  • MST Configuration
  • MST Optimization
  • Multi-Area OSPF
  • Multi-Area OSPF and Routing Table Optimization
  • Multicast Routing
  • Multi-Site Frame Relay and Policy Routing
  • Multi-Site Network
  • Named Access Lists
  • NAT overloading - PAT
  • NAT Pool
  • Network Address Translation (NAT)
  • Optimizing EIGRP
  • OSPF
  • OSPF Authentication
  • OSPF Routes
  • Policy Routing
  • PortFast and UplinkFast
  • PPP and CHAP
  • PPP with CHAP Authentication
  • PPP-PAP-CHAP
  • PVST Load balancing
  • Review Basic Router Configuration
  • Reviewing Access Lists
  • Reviewing Switch Configurations
  • RIP Routes
  • RIPv2
  • RIPv2 Routes
  • Route Redistribution
  • Route Summarization
  • Router Basics I
  • Router Basics II
  • Router Remote Access via Telnet
  • Routing Information Protocol (RIP)
  • Saving Router Configurations
  • Setting up a Serial Interface
  • Single-Area OSPF
  • Single-Site Network
  • Spanning Tree Protocol
  • Spanning-Tree Troubleshooting
  • Standard Access Lists
  • Standard Access Lists with RIP
  • Static NAT
  • Static Network Address Translation (NAT)
  • Static Routes
  • Switch and Workstation Configuration
  • Switch Basics Part I
  • Switch Basics Part II
  • Telnet
  • Testing Connectivity with Traceroute
  • Trivial File Transfer Protocol (TFTP)
  • Troubleshooting Basic BGP
  • Troubleshooting Basic Frame Relay
  • Troubleshooting EIGRP
  • Troubleshooting EIGRP Routing
  • Troubleshooting Frame Relay
  • Troubleshooting HSRP
  • Troubleshooting ISDN BRI
  • Troubleshooting Mulitlayered Switched Networks Part 1
  • Troubleshooting Mulitlayered Switched Networks Part 2
  • Troubleshooting PPP-PAP-CHAP
  • Troubleshooting RIP
  • Troubleshooting Routing Protocols Part 1
  • Troubleshooting Routing Protocols Part 2
  • Troubleshooting VoIP and Converged Networks
  • Trunking
  • Tuning QoS Mechanisms Configured with Cisco AutoQoS
  • Using Loopback Interfaces
  • Using NetSim
  • Using SDM to Configure GRE Tunnels over IPSec
  • Using the  Initial System Configuration Dialog
  • Variable Length Subnet Masks (VLSM)
  • Virtual Local Area Networks (VLANs)
  • VTP Configuration